Doctors Use 3D Models of Conjoined Twins to Prepare for Complex Separation Surgery

IMTS

Share this Article

Ximena and Scarlett Hernandez.

Ximena and Scarlett Hernandez.

There is perhaps no surgical procedure more daunting or complex that the separation of conjoined twins, even with the use of advanced 3D technology. Not only is the surgery being performed on a tiny infant, which is always delicate and dangerous, but there really is no rule book for separating these children because they are often conjoined in completely unique ways. Most birth defects have standard procedures in place that surgical teams can use as a guideline. The defects may present in different ways, but the basic specialists and surgeries that need to be involved are usually the same. But conjoined twins are very often quite unique in what parts of the body are connected, what internal structures are connected and what dangers are present when determining how to separate them.

Catalina, Ximena and Scarlett Hernandez-Torres with their mother Silvia.

Catalina, Ximena and Scarlett Hernandez-Torres with their mother Silvia.

It is estimated that one in every two hundred thousand sets of twins could be born conjoined, so it is already an extremely rare phenomenon. Even rarer is a set of triplets being born with two of the three babies being conjoined, an occurrence that is so rare that there is a one in 50 million chance of it happening. The last time that this was reported in the United States was back in 1966. But in May of 2015 Catalina, Ximena and Scarlett Hernandez-Torres were born in Corpus Christi, Texas. Ximena and Scarlett were conjoined at the pelvis; however each girl has her own set of legs. This itself is also a rarity in conjoined births, with only six percent of them being born connected in this way.

Ximena and Scarlett share several vital organs, including their colon, their uterus and a single set of ovaries. The two girls each have their own bladders, however Ximena’s kidneys are attached to Scarlett’s bladder, and Scarlett’s kidneys are attached to Ximena’s bladder. Because they share the same colon, currently both girls are being fed using a feeding tube. When the two are separated, the doctors will need to reroute both girls’ kidneys to their correct bladders and will divide the colon between them. The procedure is expected to last between twelve to eighteen hours and involve several surgical teams, including pediatric surgeons, plastic surgeons, urologists and orthopedic specialists who will need to correct each girl’s pelvis.

Ximena and Scarlett with their father Raul.

Ximena and Scarlett with their father Raul.

The same technology that has been used to create 3D models of patients’ hearts or internal organs was used to generate an interactive 3D model of Ximena and Scarlett’s complicated internal anatomy. The doctors have used the virtual 3D model of the twins to simulate the surgery, so they know what needs to be separated and what complications may occur. Not only will this process speed up the various surgeries involved in the procedure, but it will make them safer for the patients and is easier for the doctor. Virtual surgical preplanning, using 3D assets generated by CT scans and MRI data, has seen a lot of use recently, as it allows doctors the chance to know exactly what they are going to see when they open a patient up.

3dp_conjoinedtwins_rmhc_logoSilvia Hernandez and her husband Raul were told that two of their daughters would be born conjoined just three months into their pregnancy, so the couple has been preparing for this day for well over a year. And while the doctors are very confident that the girls’ separation will be completely successful, that doesn’t mean it is any easier for their parents. Silvia, who is currently staying at a nearby Ronald McDonald House, has sadly not even been able to feed her daughters on her own yet, so the upcoming surgery is weighing hard on her.

Ximena and Scarlett's mother Silvia Hernandez before she gave birth to triplets.

Ximena and Scarlett’s mother Silvia Hernandez before she gave birth to triplets.

“Since they were born, I have been waiting anxiously for them to be separated because I want to hold them separately in my arms and hold them close. But the closer the surgery day is getting, I don’t want it to happen. But of course I want it to happen so they can have a normal life. My daughters are in hands of God and his will will be done,” the girls’ mother Silvia Hernandez told CBS news.

The team of specialists being tasked with separating Ximena and Scarlett is being led by Dr. Haroon Patel from Driscoll Children’s Hospital in Corpus Christi, Texas. Most surgical procedures used to separate conjoined twins take months of pre-planning, but Ximena and Scarlett’s surgery will be especially complicated so Dr. Patel has spent nearly ten months preparing for it. The team was planning on the girls being separated last month; however, they came down with a respiratory infection that postponed it until this week. Still, the team is fully prepared for the surgery thanks to the use of advanced 3D software, so they believe that Scarlett and Ximena will be well enough to go home within three months.

Here is some video of the girls in the hospital, and you can keep up with their progress on their Facebook page. Discuss in the 3D Surgical Models for Conjoined Twins forum over at 3DPB.com.

 

 

Share this Article


Recent News

Will There Be a Desktop Manufacturing Revolution outside of 3D Printing?

Know Your Würth: CEO AJ Strandquist on How Würth Additive Can Change 3D Printing



Categories

3D Design

3D Printed Art

3D Printed Food

3D Printed Guns


You May Also Like

Featured

Pressing Refresh: What CEO Brad Kreger and Velo3D Have Learned About Running a 3D Printing Company

To whatever extent a business is successful thanks to specialization, businesses will nonetheless always be holistic entities. A company isn’t a bunch of compartments that all happen to share the...

Würth Additive Launches Digital Inventory Services Platform Driven by 3D Printing

Last week, at the Additive Manufacturing Users’ Group (AMUG) Conference in Chicago (March 10-14), Würth Additive Group (WAG) launched its new inventory management platform, Digital Inventory Services (DIS). WAG is...

Featured

Hypersonic Heats Up: CEO Joe Laurienti on the Success of Ursa Major’s 3D Printed Engine

“It’s only been about 24 hours now, so I’m still digesting it,” Joe Laurienti said. But even via Zoom, it was easy to notice that the CEO was satisfied. The...

Ricoh to Open 3D Printing Center of Excellence at North Carolina State University

Japanese 2D-to-3D printing firm Ricoh is further extending its activities in the additive manufacturing (AM) sector, this time partnering with North Carolina State University to establish a Center of Excellence....